Type 302 Stainless Steel is an austenitic chromium nickel stainless steel, non hardenable by thermal treatments. It may be cold worked to high tensile strengths with slightly lower ductility than Type 301. Its corrosion resistance is superior to that of Type 301.
302 Stainless Steel Alloy, better known as 18 8, reflects its chromium and nickel composition. 302 falls under the Stencil Grade Alloy family that is known for being easily machinable and resistant to corrosion; additionally, 302 is also a member of the Stainless Steel 300 Series.
Stress Corrosion Cracking The Type 302, 304, 304L and 305 alloys are the most susceptible of the austenitic stainless steels to stress corrosion cracking in halides because of their relatively low nickel content. Conditions which cause stress corrosion cracking are(1)
Alloy 302 is a variations of the 18% chromium / 8% nickel austenitic alloy, which is the most familiar and the most frequently used in the stainless steel family. Alloy 302 is a slightly higher carbon version of 304, often found in strip and wire forms.
Types 302, 304, 304L, and 305 stainless steels are variations of the 18 percent chromium – 8 percent nickel austenitic alloy, the most familiar and most frequently used alloy in the stainless steel family. These alloys may be considered for a wide variety of applications where one or more of the following properties are important:
Type 302 is a higher carbon, earlier version of Type 304 stainless steel, and many 302 applications have switched to Type 304 with the improvements in melting technology. Type 302 is non magnetic in the annealed condition but becomes magnetic as a result of cold working.
Penn Stainless inventory now includes Alloy 302 (UNS S30200) in sheet, sheet coil, plate, round bar, processed flat bar and tubular products. SHARE General Properties. Alloy 302 is a variations of the 18% chromium / 8% nickel austenitic alloy, which is the most familiar and the most frequently used in the stainless steel family.
Durability and Strength. Both 302 and 304 stainless steels offer .29 pounds per cubic inch density. The tensile strength of 302 and 304 stainless steels are 90,000 pounds per square inch (PSI) and 85,000 psi, respectively. Both types of stainless steel are easy to weld and create very durable welds.
Type 305 Stainless Steel is an austenitic chromium nickel stainless steel that can be cold worked and deep drawn more readably than Type 302 and Type 304 due to an increased nickel content that decreases the work hardening rate of the material. It is nonmagnetic and
Find stainless steel products like tempered steel, cold rolled steel, annealed steel and more today. Clingan supplies 300 & 400 Series Stainless in all tempers from annealed to full hard. These can be cut to length, ribbon or oscillate wound coil.
Jan 28, 2020 · 302 Stainless Steel Cold Rolled Coil Stainless Steel Coil&StripStainless steel is a steel alloy with a minimum of 10.5% chromium content, as well as certain Ni, Mo, Mn, Cu, N contents etc. Stainless steel does not readily corrode, rust or stain with water.
302 stainless steel is an Austenitic, non magnetic, extremely tough and ductile stainless steel alloy. AISI 302 annealed stainless steel is highly corrosion resistant and maintains its strength at high temperatures up to 550°F (288°C). Additionally, 302 stainless steel is non magnetic in the annealed condition and cannot be further hardened by heat treatment. As an added benefit both the
301, 302, 304 All Tempers (DQ Annealed, ¼ Hard, ½ Hard, ¾ Hard & Full Hard) 316 & 321 Annealed 17 7 Condition A & C; Austenitic stainless steel strips and straps have austenite as their primary phase. These are alloys contain chromium and nickel with a composition of iron, chromium, and nickel.
17 7 PH® is a chromium nickel aluminum precipitation hardening stainless steel that provides high strength and hardness and a moderate level of corrosion resistance up to 600˚F. This grade can be easily formed in the austenitic condition similar to Type 301 stainless steel and hardened to high strength levels using relatively low heat
We can slit 300 and 400 series stainless steel and PVC coated material with a variety of finishes to your unique specifications. We pride ourselves on precise stainless slitting to the tightest of tolerances with clean edges. We also do round edging coil to coil or cut to length for stainless steel
Stainless Steel 302 has good mechanical properties and corrosion resistance. Stainless Steel 302 is also known as AISI 302.
Our advantage:
· 20 Years of experience in the Steel field
· 500,000 MT production capacity per year.
· 100+ exporting markets covering global main countries and regions.
· 2000+ MT stock per month with different materials and sizes.
· 150+ projects each year, covering oil tank, shipbuilding, oil&gas pipeline, drilling, offshore, energy, construction industries.
Our Steel Products' Certificates:
Package: